STOCK CLEARANCE, ONLY A FEW LEFT - LESS THAN HALF NORMAL PRICE JUST TO CLEAR SOME SPACE
Vgate VAG SCAN VC210 CodeReader
The VC210 Scan is specially designed to work with VW / AUDIS, including those
equipped with the newly released Controller Area Network(CAN) Protocol.
it is small, it is capable of retrieving same information as large expensive
This recently released tool is a direct replacement for the legendary VAG 305
which is sadly now out of production.
Features and Benefits
1. Works with Volkswagen and Audi(Audi/seat/Skoda/Jetta/Golf/Beetle/Touareg/GT/Passatand
more)sold worldwide since 1990.
2. Compatible with the latest cars that require a direct CAN connection.
3. Reads and erases Diagnostic Trouble Codes (Dtcs) of Engine ABS,Airbags and
4. Turns off MIL lights of engine airbag ABS and A/T
5. Highly reliable and accurate
6. Easy-to-read backlit 2 line LCD display
7. Easy to use with one plug-in
8. Stand-alone unit with no need for an additional laptop computer to operate
9. Small in size and conveniently fits in your palm
10. Safely communicates with the on-board computers
11. No batteries needed-powered via OBDii cable
12. One-year warranty against defects
This scanner will work on most VW / VAG vehicles but exactly which control
modules can be accessed will be dependant on the actual vehicle and will vary
between vehicle model and vehicle specification.
Display: Backlit LCD, 2-line, 8 characters
Operating Temperature: 0 to 50Â¡Ã£C (-32 to 122 FÂ¡Ã£)
Storage Temperature: -20 to 70Â¡Ã£C (-4 to 158 FÂ¡Ã£)
Power: 10.0 to 15.5 Volts provided via vehicle battery
Length / Width / Height
113 mm / 74 mm / 21mm
NW: 0.25 Kg
Will it work on my Car ?
In 1996 in the
United States, a Federal Law came into force requiring all US-sold cars to be
OBD2 compliant. Most OBD2 tools are therefore advertised as working with all
cars from 1996.
The OBD2 Federal
Law applied only to cars sold in the US.
In the UK and the
rest of Europe, our equivalent law (European On-Board Diagnostics, or EOBD) did
not come into force, and more importantly, was not fully implemented by our car
manufacturers, until 2001 for petrol cars (2003/4 for diesels).
Due to this it is
difficult to know exactly what European vehicles are OBD2 compliant before the
above dates and we recommend checking with your dealer before purchasing
equipment for cars manufactured before 2001 Petrol and 2004 Diesel.
All Cars sold from
2008 use the CAN-Bus protocol.
What good does it do to measure OBD-II output?
OBD-II signals are most often sought in response to a "Check Engine Light"
appearing on the dashboard or driveability problems experienced with the
vehicle. The data provided by OBD-II can often pinpoint the specific component
that has malfunctioned, saving substantial time and cost compared to
guess-and-replace repairs. Scanning OBD-II signals can also provide valuable
information on the condition of a used car purchase.
Tell me about that "Check Engine Light".
The service industry calls the Check Engine light on your dash an "MIL" or
Malfunction Indicator Light. It shows three different types of signals.
Occasional flashes show momentary malfunctions. It stays on if the problem is of
a more serious nature, affecting the emissions output or safety of the vehicle.
A constantly flashing MIL is a sign of a major problem which can cause serious
damage if the engine is not stopped immediately. In all cases a "freeze frame"
of all sensor readings at the time is recorded in the central computer of the
Hard failure signals caused by serious problems will cause the MIL to stay on
any time the car is running until the problem is repaired and the MIL reset.
Intermittent failures cause the MIL to light momentarily and they often go out
before the problem is located. The freeze frame of the car's condition captured
in the computer at the time of the malfunction can be very valuable in
diagnosing these intermittent problems. However, in some cases if the car
completes three driving cycles without a re-occurrence of the problem, the
freeze frame will be erased.
OBD-II and your car's health
Because of their investment in the equipment required, most repair shops charge
a fee, some-times substantial, to attach the scanning equipment and diagnose
problems using the OBD-II system signals. Home mechanics and small shop
technicians have been restricted from working with these signals by the cost and
technical complexity of the equipment. With the introduction of more economical
and user friendly scanning devices, it is now practical for almost anyone to
access OBD-II signals and use them for their own testing and repairs.
Scanners vary greatly in their complexity. The best connect easily and use
software to quickly and automatically call up the OBD-II information. They
should have recording ability so that data can be collected during a test drive
without distracting the technician driving the car. A system connecting to a
laptop or desk top computer provides expanded memory for data and the ability to
export data to a spreadsheet or graphing utility.
Vgate Scan VC210 VW / VAG Group Scanner
- Brand: Vgate
- Product Code: VC210
- Availability: 1
Vgate Scan VC210 VW / VAG
IMPORTANT INFORMATION RELATING TO THE RETURN OF COMPLETE FUEL INJECTION VEHICLE KITS
The vehicle kits will normally be supplied with the ECU pre loaded with an initial start file.
This initial start file is simply provided as an aid for
engine starting, it should not be considered a suitable final
calibration for your engine.
You must be prepared to undertake further ECU calibration work to ensure the ECU files are tailored to your vehicle.
Failure to successfully complete the calibration process may lead to poor vehicle driveability or even damage to your engine.
Our Classic Fuel Injection Kits are custom built to order and to the
customer general specification and as such are exempt from automatic
return rights under Consumer Contract regulations.
By ordering this
conversion kit you understand that further ECU calibration work will be
required and the final results are outside of our control.
We cannot accept returns or claims arising from failure to successfully complete the calibration process.